Page 165 - Premdor Range Guide 2017-2018
P. 165

Moulded door general speci cation
Door speci cation
Imperial doors: 35mm (13/8”). Metric doors: 40mm / (19/16”). Fireshield doors: 44mm (13/4”). Firemaster doors: 54mm (21/8”).
Modi cation
Doors are not suitable for rebating to form a pair.
Fire doors must not be trimmed on top edge, and only up to 10mm on bottom edge and 10mm on stiles. Non  re rated doors can be trimmed by up to a maximum of 5mm off any edge.
Glazing
Glazed doors are supplied with glass safety tested to the requirements of BS EN 12600 and BS EN 12150.
Door  nishing
Moulded panel doors are suitable for paint  nish only. Door faces are supplied with a white base coat ready for on site  nishing. Base coat and priming does not seal the door fully against moisture penetration on site. For white factory  nished doors - see page 164.
Touch up paint
Order code: 43075 – Cans.
Lock block location in Standard Core doors
‘Lock’ is inkjetted on the top edge of the door on the side where the lock block is positioned. The lock block position is 880mm from the top of the door to the top of the lock block. The lock block is 360mm long. See page 171.
Bi-fold doors
Bi-fold doors have the moulded panel design on both sides and are suitable for use as room dividers or wardrobe doors. The doors are supplied pre-hinged with running gear included. Door sizes shown are nominal, with actual dimensions slightly smaller to allow for door gear and clearance.
Standard core
Economy core speci cation, with single lock block, for light duty applications. See page 171.
Semi-solid core
Semi-soild doors are made with additional core components giving a heavier feel to the door. See page 171.
Safe ‘N’ Sound
A solid core speci cation, in a standard thickness door, offering a substantial feel. See page 171.
Fire door core
Moulded  re doors are constructed using a high density chipboard panel within a timber frame. See page 171.
Fire doors
Premdor Fireshield FD30  re doors are compliant with British Standards and the BWF Certi re Scheme. See relevant data sheet for more details.
Fireshield doors are rated FD30 when hung in appropriate frame with the correct intumescent strips in the jambs and head,
or top and long edges of the door. Glazed Fireshield doors are supplied with clear (unwired)  re rated glass as standard.
Firemaster doors are rated FD60 when hung in appropriate frame with the correct intumescent strips in jambs and head, or top and long edges of door. Glazed
Firemaster doors are supplied with clear (unwired)  re rated glass as standard. Please see data sheet attached to the door.
Building regulations (England & Wales)
Moulded doors are offered fully compliant with Building Regulations where applicable.
Fire safety: Standard doors are tested to BS476 Part 22 and certi ed for use meeting Approved Document B.
Mobility: The range includes size options and glazing designs suitable for use under Approved Document M.
Acoustics: FD30  re doors have demonstrated a sound reduction value of 29RwdB, which meets the requirements
needed for  at entrance doorsets in accordance with approved Document E. When hung appropriately, in a suitable frame with  tted perimeter seals and compliant hardware. Please contact Premdor for details.
Scottish and Northern Irish Regulations may also be applicable on a Regional basis and doors are similarly compliant.
Guarantees
Guaranteed for ten years against
manufacturing defects. Guarantees are subject to the products being treated in accordance with Premdor’s instructions for storage, handling, installation, maintenance and use and exclude ironmongery where applicable. Failure to follow these instructions may invalidate your guarantee. This does not affect your statutory rights.
Trademarks
Safe ‘N’ Sound, Fireshield and Firemaster are all Premdor trademarks.
Storage and handling
Doors should be stored and handled as prescribed in the BS Code of Practice BS 8000 Part 5 1990.
Doors should be laid  at on three equal thickness bearers located along the door length to evenly distribute weight and avoid damage, and kept dry and clean inside any polythene packaging until immediately before painting. Do not store or install in an area which may be subject to extremes of temperature. Use a dry, well ventilated building, in areas which have not been recently plastered.
It is essential that precautions are taken to prevent moisture content build up. Particular care is needed in centrally heated or air conditioned buildings. Premdor must be informed at the time of tender and order whenever doors are needed for such buildings.
The testing and rapid switching on and off of heating during the construction is detrimental to joinery.
It is important that any packaging material (shrink wrap etc.) is left on the door for as long as is practically possible to avoid damage to door surfaces. This is particularly relevant to fully  nished products.
Installation
Doors should be  tted as prescribed in the BS Code of Practice BS 8000 Part 5.
It is essential that doors be fully sealed immediately after delivery. They should be sealed and knotted and primed on both faces and all four edges, and should then be fully  nished, preferably before installation.
It is essential that if the  nish is broken in any way
(e.g. trimmed, drilled or cut for letter box, hinges
etc.) then any such exposed area should be painted/ sealed. If, when installing doors, a reduction in overall size is required, it is important that equal amounts are taken from opposite edges. Allowable trim dimensions available on request.
When  tting locks and latches in doors, it is important to ensure that the construction and performance of the door is not adversely affected.
All doors should be hung 11/2 pair suitable for the weight of the door,  re doors please see data sheets provided with each door.
Finishing
Decoration should be carried out in accordance with BS 6150 and BS 8000 Part 5. Products must be clean and dry prior to  nishing, having moisture content which is no greater than the average for the intended location. Always follow the manufactures instructions provided with the paint which is to be applied.
It is important that the  nishing system is balanced
by equal application to both sides at the same time to ensure that an imbalance of moisture does not occur, particularly in the decoration of doors. The complete surface area should be fully treated with topcoat paint prior to installation. To ensure adequate coverage at least three coats of topcoat paint needs to be applied. All edges and any areas which have been cut, drilled, etc. must be fully painted to the same standard as the rest of the door.
Premdor has no control over customer applied  nishes of doors and therefore cannot accept any claims for problems of any type relating to customer  nishing of the doors.
Do not use oil (e.g. Danish oil) waxes, polishes or dyes as they do not properly seal the door. Coatings must be regularly maintained to prevent a breakdown of
the protective paint  lm, which can lead to moisture ingress/loss and deterioration of the door.
Please note
Finger-jointed materials may be used in manufacture, enhancing product stability.
16-37-346
Environmental policy
Moulded standard core doors are environmentally third party certi ed FSC®.
Semi-solid core, Safe ‘N’ Sound and Fireshield doors are all environmentally third party certi ed PEFC.
Our manufacturing and central warehouse
facility in the UK is located at Barnsley and has been independently accredited to meet the environmental management standard ISO 14001.
All of our timber based material suppliers are obligated to ensure that, as a minimum, wood is sourced in accordance with local legal forestry and logging controls, and is EUTR compliant. The majority of timber used in Premdor manufactured products is certi ed under FSC®, PEFC, MTCC, CSA or SFI approval. These schemes are recognised under guidance issued by
the Government’s Central Point of Expertise on Timber (CPET), ensuring credible environmental control. Relevant products are marked with the icon shown, based on information correct at time of printing.
Product availability
Items shown highlighted are available on a reduced lead time.
Ordering
Door prices exclude ironmongery and frames.
Except where stated, doors supplied will require on site decoration. When ordering always state product codes. All prices exclude VAT. Speci cations may vary at our discretion.
Optional Premdor aperture details are shown on pages 46 and 92.
Apertures to  re doors may only be added retrospectively by Premdor or by Premdor appointed “FAST” licensed door processors, operating as members of the BWF/CERTIFIRE scheme. Modi cations made outside of this scheme will invalidate the product certi cation.
Location and contact details of “FAST” licensees available on request.
for distributor & technical information | 0844 209 0008 | www.premdor.co.uk
165
















   163   164   165   166   167